3-Phase Meter Nimbus 100A

1.8.0 (A+) Active energy consumption total
2.8.0 (A+) Active energy supply total
5.8.0 (Q1) Inductive reactive energy consumption total
6.8.0 (Q2) Capacitive reactive energy consumption total
7.8.0 (Q3) Inductive reactive energy supply total
8.8.0 (Q4) Capacitive reactive energy supply total

C.60.9 Error messages (page is only displayed if errors are present)

• PhL Wiring error (bottle phase sequence or phases not wired)
  123: Incorrect phase sequence. 1, 2 and 3 flashing.
  1 : Only phase L1 connected. 2 and 3 flashing.
  2 : Only phase L2 connected. 1 and 3 flashing.
  3 : Only phase L3 connected. 1 and 2 flashing.
  12 : Only phases L1 and L2 connected. 3 flashes.
  1 3 : Only phases L1 and L3 connected. 2 flashes.
  23 : Only phases L2 and L3 connected. 1 flashes.

• F:F:0 ( Only displayed if one of the errors below is present)
  0x00: No error
  0xX2: Nimbus meter is not calibrated
  0xX4: Error with microprocessor, meter must be replaced
  0xX8: Software error, meter must be replaced
  0xX6: Not calibrated and microprocessor error, meter must be replaced
  0xXA: Not calibrated and software error, meter must be replaced
  0xXC: Microprocessor and software error, meter must be replaced
  0xXE: Not calibrated, microprocessor and software error, meter must be replaced
  0x1X: Logbook full

• Meter tampering symbol (magnet): 
  OBIS code C.51.6 Meter has been negatively affected.

• Terminal cover open symbol ("G"): 
  OBIS code C.51.2 Terminal cover is open.
  
  

Meter reading cycle:

• 1.8.0 and 2.8.0: Mapped OBIS codes in the memory

• 0001: Entry number in the memory 

• First line: 1.8.0 Active positive energy (supply) 

• Second line: 2.8.0 Active negative energy (delivery)

• Date and time of the entry

Open the logbook:

• Press the display button for 7-8 seconds in normal mode.

Enter the password for displaying the logbook:

• The NIMBUS Meter user receives the password from the provider.

• Pressing the button briefly increases the first digit by 1. If the digit is at 9, it changes back to 0 the next time the button is pressed.

• If the button is not pressed for 2 - 3 seconds, the system automatically switches to the next digit. This digit flashes and any number can be set again.

• If the 4th digit is set, the password entry is cancelled after 2 - 3 seconds and the password is checked.

• If the password is correct, the SMART-ME LOGBOOK screen is displayed.

• If the password is not correct, the password "FALSE" is displayed for a few seconds and the display switches back to normal mode. 

• If there is still no message in the logbook (Total : NO ENTRY), the display switches back to normal mode on display screen 2 or 3.

Exiting the logbook display:

• To exit the logbook, press and hold the display button for approx. 3 - 4 seconds. 

• If the display button is not pressed within 60 seconds, the display also switches back to normal mode on display screen 2 or 3.

C.60.9 : OBIS code of the currently displayed message 

• 0001 : Number of the stored message 0001 is the latest message.

• 8192 : Maximum possible messages in the logbook Once the maximum possible messages have been saved in the logbook, no further messages are saved ⇨ LOGBOOK FULL If LOGBOOK FULL, further changes to the calibration-relevant parameters are no longer possible without violating the calibration-related security.

• Second and third line: Identifier and type of message displayed.

• Fourth line: Date and time of the message

Log information:

• Firmware upgrade (New Firmware)

• Terminal cover opened or closed (Open, close terminal cover)

• Manipulation detected and cancelled (Start, End Meter Manipulation)

• Wiring error detected (Set, End Connection)

• New MID firmware version (New MID part)

• Time reset (Time: OLD --> NEW)

• Meter restarted (Meter OFF--> ON)

• Meter has received new calibration (New Meter Calibartion)

• Event logbook full (Last Stored Data, Logbook full)